- QHY filter wheels that are integrated (A-series cameras) or are connected to the camera using the 4-pin cable (CFW1/2/3 filter wheels) are now natively supported. This allows the native QHY camera driver to be used with these cameras and configurations.
- Alnitak Flip Flap Panel support to connect and control the panel inside the application
- Upgraded Atik driver to use latest Atik SDK and drivers
- Added a bit scaling options for Altair and ToupTek cameras to bit shift the raw data to 16 bits to be compatible with other capture software
- FreeImage library upgrade to 3.18
- Plate solvers will now receive unstretched FITS images to solve the image for a faster and even better solve result
- The autofocus crop ratio has been changed to Inner Crop Ratio, and an additional Outer Crop Ratio has been added. This lets users define centered ROI, or a centered "square doughnut" which will be used by star detection, thus avoiding stars in the center and at the edges of the FOV
- HFR calculation is now computed using the mean background surrounding the star, rather than the image mean
- HFR calculation has been enhanced to provide more accurate results, especially for imaging systems with central obstructions
- Autofocus trend lines are now using a weighted fit based on HFR standard dev in each image rather than an unweighted fit. This provides much better slopes and final focus point.
- Autofocus has been enhanced to support multiple curve fitting methodologies:
- Parabolic fitting, weighted by standard dev
- Hyperbolic fitting, weighted by standard dev
- Comnbination of parabolic or hyperbolic fitting with trend lines (average of fitting minimum and trend line intersection is then used)
- Added ability to keep guiding during autofocus
- The autofocus routine has been changed so that it doesn't attempt to measure the focus twice for the same point
- Added Spanish Translation
- Added Chinese Simplified Translation
- Added Chinese Traditional Translation
- The focuser temperature compensation feature is now turned off before an auto-focus session, and turned back on afterwards
- The NASA Sky Survey images now are automatically adjusted for brightness and contrast, depending on each image characteristic
- An autofocus filter can now be set if "Use filter offsets" is set to true. When defined, the autofocus routine will use the autofocus filter instead of the current imaging filter. Initial baseline HFR, and final HFR (used to determine whether the autofocus run was successful) will still use the main imaging filter.
- A contrast detection autofocus routine has been added. Instead of analyzing stars to determine point of best focus, the routine analyzes overall contrast of the image with various contrast detection methods. A Gaussian fit is then performed on the obtained focus points - this process can use shorter exposure times than star HFR and produce results faster
- QHY native camera driver now retrieves only the non-overscan area of the sensor
- QHY native camera driver now supports selecting readout modes with QHY600 class cameras
- Added a DATEMINUS12 placeholder to the file save pattern that shifts the current date 12 hours into the past. This allows for all images of a night to be saved into the same date folder.
- Added more manual focus targets for certain regions of the southern hemisphere sky.
- Can now configure a custom Astrometry.net API URL
- Improved status and logging for Astrometry.net plate solve jobs
- Updated Nikon SDK to latest available version (2019-10-20)
- Zooming at high magnification inside the image control will not smear the pixels anymore but show sharp pixel edges instead
- Added a reset button to sky atlas to reset all filters
- Rotator for sequence centering will now rotate to nearest orientation even if image is upside down. This is not relevant for framing after a star alignment anyways.
- Reworked Planetarium interfacing to be more robust
- Take current view center from Stellarium when no target is selected during coordinate import
- Logs older than 30 days are automatically cleaned up at application start
- Autofocus will now only show the selected fitting method
- After running an autofocus run a new json file will be written to %localappdata%\nina\autofocus containing all datapoints to retrace what was measured at a later point in time
- Guiding was improperly stopped when performing AF at start of sequence, even if DisableGuiding option was false
- QHY native camera driver will wait the full amount of time required before downloading an image from the camera
- QHY native camera driver now has a more reliable way to determine sensor bitness with CCD models
- The font size of panel IDs in Framing Assistant has been increased to a legible level
- The FRAMENR placeholder is now saving the number as 4 digits
- Framing - Rectangle panel number is now scaled based on rectangle size.
- When loading an image from a file into framing the rectangle was not calculated correctly
- Added an empty entry for Constellation Filter in Sky Atlas to unselect it
- Image File Pattern Values will now remove leading and trailing white spaces to prevent invalid file path
- In case illegal characters for a filename are inside some file patterns, they will now get replaced to still being able to save
Included Camera SDK Versions:
- Altair: 39.15529.2019.906
- Atik: 220.127.116.11
- Canon: 18.104.22.16800
- FLI: 22.214.171.124
- Nikon: 126.96.36.19901
- QHY: 0.6.0.4
- ToupTek: 30.13342.2018.1121
- ZWO: 188.8.131.52
- Native support for Finger Lakes Instrumentation ProLine/MicroLine cameras and color filter wheels
- A new equipment type "Switch" has been added which can connect to an AscomSwitch or to a PrimaLuceLab EAGLE PC
Dither without guiding
- A new Direct Guider has been added, which doesn't require a guide camera. It can only perform random dithers. It connects directly to the telescope, and will if required perform a dither via a Pulse Guide of a user-provided duration in a random direction.
- Enhanced direct guider will accept decimal durations (e.g. 0.5s), and perform random angle selection in a way that minimizes target deviation from center, even after many dither operations.
- Added interface for ASTAP, the Astrometric STAcking Program, astrometric solver and FITS viewer as a plate solver
- Mid-sequence plate solve operations (when slewing to target, or after Meridian Flip) have been enhanced to have the following behavior:
- If plate solve fails, it automatically falls back to blind failover
- If blind failover also fails, plate solve can be set to await a certain time period (by default 10 minutes) before trying again, up to a certain number of attempts (user-defined)
- If all attempts fail, or Meridian is getting close, plate solve will be considered failed, but sequence will continue as usual
- Added options to adjust downsample factor and maximum number of considered stars for ASTAP and local astrometry.net solvers
GPS Assisted Location
- Added a NMEA GPS interface to retrieve the current location
Interfacing with planetarium programs
- NINA can interface with Cartes du Ciel, HNSKY, Stellarium, and TheSkyX through their repsective TCP services to import the selected object for use in the Sequence Editor and Framing Assistant, as well as setting the observing location to match that which is set in those programs
- Inside the camera selection there is a new entry for "Manual Camera".
- This simulated camera will enable the use of cameras which lack an SDK, while still using the whole N.I.N.A. workflow.
- It will watch a specified folder for newly created files. These files will be stored inside an internal queue.
- Each time the application wants to download an exposure from the camera, the first item of this file queue is resolved and loaded into N.I.N.A.
- Additionally a manual Bulb Mode trigger can be activated, so it will use the selected Bulb Mode in Settings->Equipment->Camera on Exposure Start.
- When this trigger is deactivated the application will just skip the Start Exposure and wait for another file to roll into the specified folder
Weather data sources
- The existing OpenWeatherMap implementation has been replaced with a full weather data interface.
- The new interface allows devices with ASCOM ObservingConditions class drivers to supply N.I.N.A. with weather data and other conditions.
- Native OpenWeatherMap functionality is maintained, and any configured OWM API key is retained and utilized by the new native OWM client.
- Weather data sources are now configured under the Equipment section.
- Any available weather data types (air temperature, pressure, wind speed, etc.) are inserted into images as FITS keywords and/or XISF image properties.
- Quick focuser movement buttons have been added (fine/coarse move IN/OUT) to the focuser views
- A new focuser settle time parameter has been added, in case the focuser shifts the image when moving (SCT, lens belt focusing, etc.). This should help with auto-focus in particular.
- Focuser backlash (in and out) can now be specified. The backlash will be applied to focuser movements whenever the focuser reverses directions.
- A new Measure Backlash tool has been added in the Auto-Focus view in the imaging tab. When launched, NINA will automatically measure focuser backlash IN and OUT.
- Sequence Auto-Focus can now be triggered if measured HFR of any frame is X% worse than the first frame taken after the previous auto-focus routine.
- More resilient autofocus:
- Ability to automatically reattempt autofocus from scratch several times in case it failed
- Automatically go back to original focus position if obtained HFR is significantly worse than original
- Ability to take multiple autofocus exposures per focus point and average their HFR. This leads to smoother autofocus curves.
- A crop ratio has been added to the autofocus, letting users autofocus only on the center of the frame
- Autofocus can now be set to use only the top brightest stars, so the same stars are used throughout the autofocus routine. This will work best on sparse star fields, and for stable, well-aligned equipment (e.g. so stars don't move between auto-focus exposures)
- Ability to use binning for autofocus
- End of Sequence Options are now available, which include:
- Parking the telescope - This will stop the guiding, and invoke the mount Park method if available, otherwise the mount will slew to near the celestial pole (on the same side of Meridian it last was) and stop tracking. Before using this in production, test out the feature at the telescope, with your finger on the power switch. This is to avoid any crash into the pier for mounts that do not have limits.
- Warming the camera - the camera will be slowly cooled, with the cooler eventually turned off
- A pre-sequence check is now triggered, and will notify end users of a variety of potential issues (camera not cooled yet, guider not connected, telescope not connected but slew enabled, etc.) at sequence start
- It is now possible to reset the progress of a sequence item, or of a whole sequence target. If an item that occurred prior to the active sequence item is reset, stopping and starting the sequence will get back to it, but pausing/playing will keep going from the current item.
- The sequence start button is unavailable if an imaging loop is in progress in the imaging tab
- If telescope is capable of reporting SideOfPier there will now be a new option to consider this for calculating the need for meridian flips
- It is now possible to set the Offset in addition to the Gain within each sequence item
- Added buttons to move sequence row up and down the list
- File handling now changed so that:
- the default folder for sequences is set under Options -> Imaging
- a 'modified' status is maintained for each target
- targets can be loaded from any xml file
- targets can be saved back to the file it was loaded from
- a 'Save as' option is added to save to a new file
- a warning is issued if a target is closed without saving when it has been modified. This also applies when the application is closed.
- Controls to change order of targets in a multi-target sequence
- Ability to save and load 'target sets' (a set of targets in a certain sequence)
- Progress bars have been added for remaining filters and exposures
- A new Slew to Zenith button has been added for easier flats. This includes an option for east or west pier side, depending on which side of pier the mount should approach zenith from.
- A new option to pause between filters has been added. This is to allow the user the chance to set lightbox settings
- Imaging tab - Equipment specific views will only show the "Connected" flag when the device is not connected to save space
- Added a layout reset button to the imaging tab to restore the default dock layout.
- Equipment chooser dropdowns are now grouped by driver categories to easily distinguish between for example ASCOM drivers and other vendor drivers
- All FITS keywords now have descriptive comments with units of measurement noted if applicable
- FITS keyword
DATE-OBS now has millisecond resolution, eg:
- Additional FITS keywords are now added to images if their associated data is available:
DATE-LOC: Date and time of exposure adjusted for local time
FOCRATIO: Focal ratio of the telescope, user-configurable under Options->Equipment->Telescope
SET-TEMP: The configured CCD cooling setpoint
SITEELEV: Elevation of the observing site, in meters
N.I.N.A. <version> <architecture>
TELESCOP: Telescope name if provided under Options->Equipment->Telescope. Falls back to ASCOM mount driver name
OSC Camera Handling
- Debayering is now applied prior to plate-solving or auto-focus star detection
- An Unlinked Stretch option has been added. When enabled, color channels will be stretched separately, helping hide the sky background. This results in more visible celestial objects, and helps enhance both autofocus and platesolving reliablity, especially in light polluted areas. Processing time is however increased.
- A Debayered HFR option has been added. When enabled, the HFR computation will be made on the Debayered image rather than the Bayered array, providing better Auto-focus results
Star Detection Sensitivity
- Star Detection has been enhanced to detect more stars more accurately, while avoiding picking up noise by checking that the star is a local maximum and has sufficient bright pixels
- In addition, a new Star Sensitivity Parameter is available in the Imaging options. It has three settings:
- Normal: use standard NINA star detection
- High: More sensitive method, with little to no performance impact. Typically picks up 1.5x - 2.5x more stars than Normal
- Highest: Most sensitive method, with some performance impact. Typically picks up 1.5x - 2.5x more stars than High
- The higher the detection level, the more likely lumps of noise are liable to be picked up (despite rejection parameters to avoid that)
- A noise reduction parameter has been added for better star detection in fairly noisy images, which can be important if using High or Highest star sensitivity levels, although the Normal sensitivity level will also benefit from it. Several settings are available:
- None: no noise reduction on full size image done before star detection
- Median: a Median filter is applied to the full size image before star detection. This is good if the sensor has many hot pixels, but time consuming
- Normal: a standard fast Gaussian filter is applied to the full size image before star detection. This is good for smoothing out the thermal and bias noise of the sensor
- High: a strong fast Gaussian filter is applied to the full size image before star detection. This is for fairly noisy images, but can make star detection more difficult
- Highest: a very strong fast Gaussian filter is applied to the full size image before star detection. This is for noisy images, although star detection may suffer
- Fixed when FramingAssistant was not opened before and a DSO was selected from the SkyAtlas as Framing Source an error could occur
- Fixed scrolling through Framing Assistant Offline Sky Map while cursor was inside Rectangle ignored zooming
- Fixed Alitude charts displaying wrong Twilight/Night predictions for some scenarios
- Manual focus target list was not updating in some scenarios. Now it will always update. The interval for updates is one minute.
- Fixed an issue in FramingAssistant when reloading the image and having multiple panels selected, that the orientation was not considered properly resulting in wrong coordinates
- Fixed an issue in the Telescope Equipment tab that could potentially slew to the wrong Declination if the declination angle was negative
- Fixed issues in the subsampling logic for ASCOM, ZWO, and QHY cameras - the origin coordinates are now properly set, and take binning into account
- Fixed a race condition that caused HFR to not be computed for frames right before autofocus in some instances
- Fixed an issue for Nikon SDK that looked into the wrong folder for the external md3 files.
- Fixed a bug where Platesolve Orientation was displayed as negative and also throwed of the rotation centering when using rotators.
- Fixed a bug in Autofocus routine that could wrongly declare an autofocus run a failure if the starting point couldn't detect any stars
- Fixed custom color schema not saving properly and resetting to default when reloading the application
- The backlash measurement routine has been fixed so that the focuser is properly recentered before the backlashOUT measurement procedure
- Some Sky Surveys did not work in some locales due to decimal pointer settings
- When EOS Utility is running in the background, the x64 N.I.N.A. client will scan for this app and prevent a crash due to the EOS utility being open. Instead a notification will show up to close the EOS Utility.
- N.I.N.A. SQLite Database will be created on demand and migrated to new versions on application startup instead of just being overwritten by the installer.
- Setup Installer can be run in fewer clicks and is also capable of launching the application after successful installation.
- Image History Graph will only contain statistics from sequence items
- Further increased parallelism during sequencing.
- After capture during image download: Parallel dither and change filter (if required)
- After download: Parallel image saving and processing to display the image
- Image HFR is now available as an image file name token (
- Focuser Temperature is now available as an image file name token (
- Added a clear button on HFR History graph. The button will be displayed when hovering the control.
- A new button is added in the options to directly open the log destination folder
- Added option to adjust USBLimit for Altair and Touptek cameras. This can prevent potential black preview screen issues. More details on this topic described at altair: https://altaircameras.com/black_preview_screen/
The N.I.N.A. team would like to sincerely thank:
- The staff at Cloud Break Optics and Finger Lakes Instrumentation for arranging a ProLine PL09000 and CFW1-5 to assist in integrating native FLI camera and filter wheel support.
- Filippo Bradaschia from PrimaLuceLab for providing an EAGLE unit to implement direct interfacing with the EAGLE Manager
Included Camera SDK Versions:
- Altair: 39.15529.2019.906
- Atik: 184.108.40.206
- Canon: 220.127.116.11
- FLI: 18.104.22.168
- Nikon: 22.214.171.12401
- QHY: 0.5.1.0
- ToupTek: 30.13342.2018.1121
- ZWO: 126.96.36.199
Version 1.8 Hotfix 1
- Prevent an unnecessary profile saving on application start
- Profiles where always saved after a sequence exposure, which slows down the image saving process. During sequence capture the profile saving is disabled now.
- Enable/Disable sequence entries
- Added interface for All Sky Platesolver
- Altair native driver support
- ToupTek native driver support
- QHYCCD native driver support
- Added support for anti-dew heaters in ZWO cameras
- On ASCOM drivers support for setting readout modes
- Add SkyAtlas image source which allows for framing based on offline SkyAtlas data
- Supports you taking flats
- Added a list of manual focus targets (bright stars) that are currently visible in the sky
Framing Assistant Offline Sky Chart
- Based on Sky Atlas data a basic sky chart showing objects can be displayed
- Instead of dragging the rectangular through the initial image like in the other framing sources
the background itself will be moved like in an orrery
- Added Synchronized PHD2 Guider (experimental)
- Synchronized PHD2 Guider will synchronize your Dither requests between multiple instances of N.I.N.A.
- Known limitations: Dithering will happen every possible synchronized frame and is not changeable
- Previously the auto update was always just looking for released versions. Now multiple sources (Release, Beta and Nightly) can be selected and the auto updater updates to the respective version accordingls.
- Additionally the changelog for the new version will now be displayed prior to updating, too.
- Corrected Max Binning level for ASI Cameras
- Focuser move command fixed where lots of move commands where sent by accident
- Rotation value now considered for sequence import|export
- Canon: Fixed bulb mode for exposure times <30s
- Canon: All shutter speeds now correctly added when step set custom function is set to 1/3
- Meridian Flip window does not get stuck anymore when clicking on cancel
- Log Level will now be set on application start based on profile settings.
- ASI Cameras will not shut down their cooling and progress on opening multiple instances of NINA
- In some cases the application stayed open in the background after closing. This should not happen anymore
$$TIME$$ will now use timestamp on exposure start, not on exposure end
- Fixed Meridian Offset default values for plate solved polar alignment
- On sequence target guiding will be paused, prior to slewing to a new target
- Autofocus will not trigger a pause/resume command anymore, as this was not reliable in some cases. Instead PHD2 is stopped and started, similar to what is done during meridian flip.
- Fixed Platesolve result reporting wrong Dec Error.
- Platesolve recenter now considers proper angular distance calculation instead of relying just on Right Ascension.
- Clear button for PHD2 Graph
- Hide camera cooler controls when not available for current camera model
- Zero Floating point numbers now displayed as "0.00" instead of ".00"
- Show better exception message when an ASCOM Interop Exception occurs
- Canon: Errors are now shown to users in a readable format if any occur
- Removed hard requirement of ASCOM platform. Application can now function without it
- Improved UI Style.
- New logo
- Better version display
- Tweaked some color themes for more consistent colors
- Better spacing between elements to reduce wasted space
- Two new background colors to better pronounce some ui elements
- Reworked Imaging tab to have a common style.
- Imaging tab tools pane (to hide/show panels) moved to the top and split into two separate categories
- Profiles don't get overriden when using multiple instances of N.I.N.A. with each one having a separate profile active
- Autostretch replaced by a better midpoint transformation function
- Autostretch now has black point clipping options
- Vastly improved image statistics calculation time.
- Estimated Finish Time will automatically update in the sequencing view
- Added copy button for existing color schemas to copy over to custom and alternative custom schemas
- Framing tab:
- Moved coordinates out of framing boxes to not obscure target
- Added a new button to be able to add the framing target to a sequence instead of replacing
- Control to adjust opacity of framing box
- Improved Framing Assistant and Sequence Target Textboxes by giving up to 50 target hints based on input to select from
- Framing Assistant now can annotate DSO
- Sensor offset is now available as an image file name token (
- Attempt to start PHD2 and connect all equipment when connecting to guider and PHD2 is not running
- Adaptive Cooling: Duration for cool/warm camera is now a minimum duration. In case the cooler cannot keep up with the set duration, the application will wait for the camera to reach the checkpoints instead of just continuing setting new targets without the camera having any chance to reach those in the timeframe.
- Automatically import filter wheel filters to the profile on connection when profile filter list is still empty
- Load a default imaging tab layout in case the layout file is corrupted or not compatible anymore
- Removed Altitude Side combobox from plate solved polar alignment. It will be automatically determined based on alt/az coordinates.
- Changed log file format. Each application start will write to a separate log file for better distinction
- Improved XISF save speed and resulting file size by not embedding the image as base64 string, but instead as attached raw byte data
- Additional FITS keywords are now added to images if their associated data is available:
OBJECT: The name of the target, as supplied in the active Sequence
RA: The DEC and RA of the telescope at the time of the exposure
INSTRUME: The name of the connected camera
OFFSET: The sensor offset, if applicable
FWHEEL: Name of the connected filter wheel
FOCNAME: Name of the connected focuser
FOCUSPOS: Position of the focuser, in steps
FOCUSSZ: Size of a focuser step, in microns
FOCUSTEM: Temperature reported by the focuser
ROTNAME Name of the connected rotator
ROTATANG: Angle of the rotator
ROTSTPSZ Minimum rotator step size, in degrees
- Applicable XISF Image Property analogs of the above, as defined by XISF 1.0 Section 11.5.3
The N.I.N.A. team would like to thank
- Nick Smith from Altair Astro for providing a GPCAM2 290C to integrate Altair SDK
- Elias Erdnuess from Astroshop.eu for providing multiple Toupcam Cameras to integrate ToupTek SDK
- The staff at QHYCCD dealer Cloud Break Optics for lending a QHY183C to integrate QHYCCD SDK
These items helped a lot during development and testing.
Thank you for your support!
- Mosaic planning for framing assistant
- Added multiple new SkySurveys to choose from for framing
- DSLR RAW files can now be loaded into framing assistant
- Sequence multiple target planning. Import/Export also available
- Consider Rotation for framing assistant when set for a sequence during platesolves
- Added a manual FilterWheel for users without a motorized wheel or with a filter drawer. There will pop up a window and prompt the user when a filter change is requested
- Support for ASCOM Rotators added
- A manual rotator option is added, for users without an automatic rotator. A pop up will show with the current angle and target angle for a user to manually rotate to
- DSLR Users: Images will now always be saved as RAW to prevent any loss of data due to conversions
- Aberration inspector added to imaging tab. It will show a 3x3 Panel containing the current image
- Battery display for DSLRs
- Added ImageParameter
- Latitude and Longitude can now be synced from application to telescope and vica versa (when supported).
- Serial Relay (via USB) interaction for Nikon Bulb
- Fixed Canon issue that a second exposure is accidentally triggered, causing the camera to be stuck
- Fixed memory leak when using Free Image RAW Converter
- Guider is also connected when pushing "Connect All"
- Changed FilterWheel UI for switching filters
- Some improvements to memory consumption
- Automatically triggered Autofocus and Platesolving now spawns inside a separate window
- Guiding Dither thresholds now configurable
- Flipped + and - for Stepper Controls
- Minor UI Layout improvements
- Made SkySurvey Cache directory configurable
- Local astrometry.net client will now downscale image for faster image solving
- ImagePatterns inside options can now be dragged from the list to the textbox
- Major code refactorings for better maintainability
- Lots and lots of minor bugfixes and improvements